8 inch ford rear end identification.

Ford Rear Axle Assembly Identification - Page 02. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL. or. L. Identifying The 7.5-Inch 10-Bolt. Although the 7.5-inch 10-bolt closely resembles the 8.5-inch housing, you can positively identify the Chevy 7.5-inch rearend by measuring it. The oval-shaped cover measures 8 5/16 inches by 10 9/16 inches. The distance between the bottom center bolt in the cover and its adjacent bolts is 3 1/4 inches.The image below shows the Safety Label of a Ford Truck. From the arrow, you can see the axle code is H9. As you proceed to the Ford Axle Code chart, you will notice that the table indicates it has a Ford 8.8″ Limited Slip Differential with an Axle Ratio of 3.55. Find the axle code from the Safety Compliance Certification label.Ford Rear Axle Assembly Identification - Page 13: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: S406-B: Ford F250SD, F350SD Pickup '99: 3.73: 10.50: NL--S406-C: Excursion '00 Ford F250SD, F350SD Pickup '99-01:

Does anyone know what car this rear end housing would be out of by the measurements.It is 54 3/8" from outside to outside of the flanges.It is 43 1/4" from center to center of the spring perches.Where it tapers down the smaller part of the tube is 2 3/4" in diameter.The nodular center section has 3.91 gears and is a Traction Lok.I dont know if the housing and center section are original ...Speedometer gear uSage chart — 7.5" and 8.8" axle. The chart specifies the driven gear recommended to obtain approximately correct mph readings when the listed Ford Racing ring and pinion gear sets are used in conjunction with the indicated speedometer drive gear and Mustang original equipment. 15"/16"/17" tires (800-815 revolutions/ mile)."Another fairly common 9-inch case is the "WAR" casting, with two 12- and 6-o'clock ribs, very similar in appearance to the smaller '67-and-up 8-inch case, and the heavy-duty 9-inch "N" case. The "WAR" case doesn't employ the high nodular-iron witnessed with the C7AW-E case mentioned earlier.

Aug 25, 2020 ... On todays episode of Explained, we go over the main differences between a Ford 9-Inch and a GM 12-Bolt rearend and which application may ... Ford Rear Axle Assembly Identification - Page 13. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL. or. L.

Nitro Gear & Axle (6) Richmond Gear (5) USA Standard Gear (5) Yukon Gear & Axle (4) Excel Ring Pinion and Axle (2) Get Results; Ring and Pinion Ratio. 3.55:1 (7) 3.80:1 (7) 4.11:1 (6) ... Ford 8 Inch 3.00 Ratio Ring And Pinion. Part Number: NGA-F8-300-NG. Not Yet Reviewed. Estimated Ship Date: Jul 15, 2024 if ordered today. Free Shipping ...Ready to complete your budget rear axle overhaul? In this final installment of our series, join us as we guide you through every step of how-to assemble the ...2010-2011 Ford Ranger 8.8-inch Axle - 58.50 inches *. 1991-2003 Ford Explorer 8.8-Inch Axle - 59.625 inches. * The 2010-2011 Ford Ranger 8.8-inch axle is actually narrower and has shorter shafts than the 2009 and earlier models. Ford used rear disc brakes on the 2010-2011 Rangers, so Ford Shortened the axle housing and shafts to compensate for ...1330 rear end yoke for 9 inch ford 9000472 pinion yoke kit 1330 series 28 splines 4 inches tall fits ford Ford 8.8 parts-broncograveyard.com 1350 yoke for ford 8.8 – desolate motorsports ... Rear ford end inch identification mustang axle help ranger diff differences between gt guide forums trucks tech offline 1995 axlesFord pinion yoke 1330 ...Ford 8 inch rear end with original center section. Pre-Owned. $500.00. dkroll2719 (389) 100%. or Best Offer. Free local pickup. FORD 8 INCH 8" REAR DIFFERENTIAL 39 TOOTH 28 SPLINE YOKE END C70W 4025A 3.0 gear. Pre-Owned. $899.99.

Most likely you have an 8" rear though. At first glance it looks like a 9", but there are some differences and it's not as strong. The sure way to tell if it's a 9": On the front side of the housing is a ring of studs w nuts that hold the cast iron center section to the housing. Try to put a socket on the bottom two nuts.

I picked up a new 66 body that used to be a 6 cyl. but some one has converted it to a 5 lug. I want to find out what rear end it is because I am putting in a 351 windsor into it. The other question I have is that the 1966 289 mustang coupe car I am selling is set up different in the rear end. The support bars for the rear end come almost all ...

Ford 9 Inch Rear End Identification Numbers 19 Dec 2023. Identify front and rear differentials Ford identify inch rearend rear end differential difference between tell source 7 3/4" rear end. Ford 9 Inch Identification - Hot Rod Forum : Hotrodders Bulletin Board. F250 differentials axle Identifing ford rearends Rear end identification ford mustang4.11 to 1 axles: WCZ-J. 4.30 to 1 axles: WFU-E. WFD-C. WFD-E. Decoder for Ford 9-inch Tags.Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: WDD-B: Ford Pass., Mercury '65: 3.00: 8 3/4 inImages presented for reference and educational purposes only. To have an image removed from this website, please contact us at: [email protected]. Ford 8" Differential parts are in stock and ready to ship today at West Coast Differentials. Call our Rear-End Parts experts for LIVE help.Boat735. One way to get old bearings off is to use a cut off wheel and cut through them carefully without damaging the axle. Another way is to take them to a machine shop and have them pressed off. The new one's need to be pressed on so you may as well have a machine shop do it (or any place with a press).

mustangboy. 6653 posts · Joined 2002. #2 · Feb 2, 2002. No the 8 and 8.8 rears are not the same.The 8inch is basically just a slightly smaller version of the 9 inch. The 8 and 9 inch rears have removable "pots" that go into the front of the axle housing as a complete assembly.The 7.5 and 8.8 rears used in the newer Fords have a cover that ...11 posts · Joined 2010. #1 · Jul 5, 2011. I am trying to identify what kind of axle I just purchased. I was told it came out of a '66 Mustang Coupe with a 289. The axle tag reads: WCZ-E 2.80 6AD 930. According to fordifcation.com they identified this axle coming out of a '65-'66 Mustang with a 2.80 axle ratio and a 7-3/4" ring gear.The aftermarket considers this an 8 inch diff. Ford is being specific on the ring gear diameter. The diameter is determined by the number of teeth that are on the gear. If you were to get a different gear ratio it may measure 8 in or it may fall in between 7 3/4 in or 8 in. To get parts just refer to it as an 8 inch. The backlash can be adjusted.When it comes to understanding the various components of a vehicle, the rear axle is often overlooked. However, for those who have a passion for off-roading or are simply intereste... You are here: Home Tech Articles Front / Rear Differentials Ford Rear Axle Identification - Page 02. ‹ Back to Technical Index. Ford Rear Axle Assembly Identification - Page 02. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL or L. Axle Shaft Splines.

The aftermarket considers this an 8 inch diff. Ford is being specific on the ring gear diameter. The diameter is determined by the number of teeth that are on the gear. If you were to get a different gear ratio it may measure 8 in or it may fall in between 7 3/4 in or 8 in. To get parts just refer to it as an 8 inch. The backlash can be adjusted.Like the 9-inch, the Ford 8-inch is a third member-type carrier assembly for the banjo-type rearend. This means it unloads from the front and utilizes a third pinion bearing to give it extra support. This extra support helps reduce twisting of the differential when under load. The 8-inch uses the same axles as the larger 9-inch, which adds to ...

My video on how to change the gear oil in a rear differential or rear end. These are universal instructions for most vehicles. It is an easy repair or replac...Re: Rear End with no tag how to ID. by two-bit » Fri Apr 08, 2016 8:09 pm. Sounds like an 8.8 with a '97 casting number. Pull the cover and look for the numbers. Should be stamped on the ring gear. It will be a combo number like: 41 10 or 40 13 or 45 11. Those are the number of teeth on the ring gear and the pinion.Nitro Gear & Axle (6) Richmond Gear (5) USA Standard Gear (5) ... Ring and Pinion Gear, Ford 8 Inch 4.11 Ratio Ring And Pinion. Part Number: NGA-F8-411-NG. Not Yet ...7496 posts · Joined 2001. #7 · Oct 24, 2008. Where it reads 2 79. There should be a decimal between the 2 and 7 if you look for it.... Anyway, 2 . 7 9 is an open (non trac-loc) 2.79 ring and pinion. If it was 2 L 7 9 then it would be a trac-loc. The above assumes it hasn't been changed.Ford Rear Axle Assembly Identification - Page 01. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL. or. L.28 SplineYou must remove one axle from the rear end to identify the spline count.wrap a piece of paper around the teeth to count the teeth or use a marker to...Ford 9" : what year i have to locate parts?Ford 8.8 rear end width chart. Ford differential identification axle tag rear codes info front tags truck trucks identifying parts thanks9 inch rear end Ford truck 9" rear end disc brake conversion kitRatio gear differential rear inch gears ranger ford final semi chart truck tires wheels australia ...

Ford 8.0 Ring and Pinion Part Number, Tooth Count & Ratio. Your gears run cooler and last longer! Order above high performance synthetic oil and friction additive combo kit at time of order for ring and pinion or bearing overhaul kit and pay only $63.95 plus S&H, a $69.00 value.

IIRC the only trucks that come with the 8.8 rear is the 3.5L N/A trucks. The 5.0L and all others come with the 9.75. That was true up until the '15 model year, Tim. For '15+ the only trucks that always have the 9.75" axle are those with the 3.5L EcoBoost engine. Max Tow might put the 9.75" under a 5.0L truck, but the majority of them have …

According to Nasty Z28, the GM/Chevrolet 12-bolt rear end was manufactured from 1965 through 1971. After that, GM instituted the "Corporate" rear end, a 10-bolt rear end that integrated feartures of both the 10- and 12-bolt rear ends. Rear ends with measurement designations are named after the diameter of the ring gear, i.e. 7.2 and 8.5 inch.Reviewed by: Scott from Orono, MN. - 5/3/2016. /. Ford 8" Third Member. I previously bought an 8" third member with 4.62 gears and it was fantastic in my 70 mustang. I have another 70 mustang I'm building, more for the street, and got the same 3rd member but with 3.80 gears. Much more freeway friendly.When it comes to getting power to the pavement, GM's 10-bolt, 8.5-inch rear end with Positraction is a hero. Like Superman in street clothes, however, it can be hard to identify this beefy unit among its weaker cousins, the 10-bolt, 8.2-inch with open differential. GM built countless thousands of both types of 10-bolts from 1970 to 1994.3783 posts · Joined 2009. #16 · Apr 8, 2010. The 9 inch Ford Traction Lock always uses ring gear bolts with a 5/8 head. The standard differential uses ring gear bolts with a 3/4 head, unless the gear has been installed with after market bolts. The 3/4 head will not fit the TL differential.The question is whether a car has an 8-inch or 9-inch Ford. An identification might be needed while looking for a donor rear in a salvage yard, or trying to find out what is in one’s own car. Some 8″ housings look like the early “smoothy” 9-inch housings, so merely peering under a crusty undercarriage will hinder a correct I.D.Ford Rear Axle Assembly Identification - Page 05: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: WDY-A, A1: Comet '66-69 Fairlane '66-70 Falcon '66-70 Montego '70-74 Torino, '71-'74: 3.00: 8 in: NL: 28-Ford Rear Axle Assembly Identification - Page 07: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft ... Ford Pass. '82-'83: 3.42: 8.5: L: 28-WFC-G: Capri, Mustang, Cougar 82 Fairmont, Zephyr, Granada 82 Lincoln Continental '82 Thunderbird 82: 3.08: 7.5: L: 28-In 2015 Ford Introduced a newly designed 8.8" Rear-End they called the "Super 8.8" It replaced the older 8.8" rear that had been in production for some 25 years, and parts from these two do not interchange. The newer "Super 8.8" comes in 2 flavors 1. A solid axle model designed for the 2015+ F-150 light duty pickup. 2.Differential Identification. Dana Dana 30 - Standard, Reverse Rotation, CS & TJ Dana 30 - JK ... Ford Ford 7.5" Ford 8" Ring Gear Diameter: 7.5" Ring Gear Diameter: 8.0" Pinion Diameter / Spline: 1.625" / 28 Pinion Diameter / Spline: 1.188" / 25How can you identify which rear axle you have? It can be narrowed down this way:1. Rear brake drum backing plate - Finding the number etched in2. ... Rear brake drum backing plate - Finding the ...But these trucks are old, and have usually been thru several owners. To make sure what you actually have under your truck, jack up the rear end and turn one wheel while observing the other. If the other wheel turns the same direction, you have a limited slip diff. If it turns in the opposite direction, then you have an open diff.

1948 - 1956 F1, F100 & Larger F-Series Trucks - Help! 9" Ford axle shaft identification - Ok thanks guys for the help thus far. Here's the deal, I've got what appears to be mix-matched axleshafts in the Heinz-57 rear axle in my '56 F100. Here's what I do know- the housing is a 67-72 housing and the backing...The code can be found on the Vehicle Identification Number (VIN) label, which is typically located on the driver's side door jamb or the front windshield. 2. Decoding the Axle Code. To decode the Ford Axle Code, you need to refer to the manufacturer's specifications or consult an online decoding tool. The code is made up of several ...Dana Differential Identification. The Bill of Material (BOM) number is used to identify Dana differentials. Traditional BOM's are six digits long and begin with the number 60 or 61 followed by 1 or 2 digits, such as 605561-1. Later-model BOM's may start off with the first three digits of 200 rather than 60 or 61, for example 200561-1.269 posts · Joined 2012. #5 · Jan 14, 2013. The tag info you posted would be from an 8" differential. The 2.79 indicated ratio is 8" only. 9" equivalent ratio would be 2.75 for 1967. Best, Al.Instagram:https://instagram. duke outage map ncmarkiplier ethnicitymoviesanywhere com activate codehominy falls 66mustang86. You have to take a pic of the front of it where the pinion comes out for me to tell for sure but it is a 8 or 9 inch rearend. Most likely an 8 inch as they were standard on these cars. You refill it from that screw in plug on the back of the main housing halfway up. Fill it until it reaches this level and starts coming out and then ...You are here: Home Tech Articles Front / Rear Differentials Ford Rear Axle Identification - Page 02. ‹ Back to Technical Index. Ford Rear Axle Assembly Identification - Page 02. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL or L. Axle Shaft Splines. pars car salesderek thomas mlb umpire It is 3.07 gear, open, 8.8" (it would say 3L07 if it were limited slip) Only Mark 8's and new cobra IRS's get the aluminum center section. Same thing as 89-97 tbirds and cougars. Only the super coupes and xr7's got the 8.8 though, base models got 7.5" irs. Mark 7 was fox chassis, making it a solid axle. walmart healthy benefits plus FORD REAR END WEIGHT COMPARISON 8" vs. 9" 8-inch Rear End Assembly Weight : 170 lbs. 1. Housing: 36 lbs. 2. Axles: Medium Journal, 28-spline -15 lbs. ea. 3. Brakes: Small 10" x 1¾" Drum Assemblies - 22 lbs. ea. 4. 3rd Member: Reinforced Revision 8-inch Case - 60 lbs. 9-inch Rear End Assembly Weight: 194 lbs. 1. Housing: 38 lbs. 2. Axles: Large ...The silver placard will be labeled "Service Parts Identification" and includes a bunch of three-digit codes. The prefix for GM RPO codes relevant to Axle Identification is almost always "G". We call them G codes…look for G80, GT3, etc. Occasionally an "F" or "H" prefix will be used when referring to Axle Identification.7496 posts · Joined 2001. #7 · Oct 24, 2008. Where it reads 2 79. There should be a decimal between the 2 and 7 if you look for it.... Anyway, 2 . 7 9 is an open (non trac-loc) 2.79 ring and pinion. If it was 2 L 7 9 then it would be a trac-loc. The above assumes it hasn't been changed.